Différences
Ci-dessous, les différences entre deux révisions de la page.
Les deux révisions précédentes Révision précédente Prochaine révision | Révision précédente Prochaine révision Les deux révisions suivantes | ||
documentation:hardware_drivers_ui_tools:bcnc-autolevel [2017/10/07 09:26] admin |
documentation:hardware_drivers_ui_tools:bcnc-autolevel [2017/10/08 10:55] admin |
||
---|---|---|---|
Ligne 1: | Ligne 1: | ||
- | ====== bCNC - AutoLevel ====== | + | |
+ | ====== Gravure de PCB - procédure avec nivelage automatique ====== | ||
+ | |||
+ | //[[https://github.com/vlachoudis/bCNC/wiki/PCB-101-First-time]]// | ||
+ | //[[https://github.com/vlachoudis/bCNC/wiki/AutoLevel]]// | ||
\\ | \\ | ||
\\ | \\ | ||
- | //[[https://github.com/vlachoudis/bCNC/wiki/AutoLevel]] | + | |
- | //[[https://github.com/vlachoudis/bCNC/wiki/PCB-101-First-time]] | + | ===== 1. Nettoyez la face cuivre du PCB ===== |
+ | Avec de la laine de verre ou un papier abrasif, genre 400. | ||
\\ | \\ | ||
+ | ===== 2. Fixez le PCB sur le martyr ===== | ||
+ | Le PCB doit être maintenu bien à plat. Utilisez des brides. Le double face fonctionne aussi. | ||
+ | |||
+ | |||
\\ | \\ | ||
+ | ===== 3. Montez le 1er foret sur la broche ===== | ||
- | ===== PCB 101 First time ===== | ||
- | ==== 1.Clean Copperclad PCB with steel wool or equivalent until shiny ==== | + | \\ |
- | //If you skip this step, you may damage a tool bit when probing.// | + | ===== 4. Alumez la CNC et démarrez bCNC ===== |
- | ==== 2. Clamp Copperclad PCB to waste board ==== | ||
- | //Want PCB to be held down "flat" and secure Double-backed tape works well for some.// | ||
- | ==== 3. Mount First Drill bit in Router ==== | + | \\ |
+ | ===== 5. Dans bCNC connectez la CNC ===== | ||
+ | * Sélectionnez le menu **Fichier**. | ||
+ | * Sélectionnez le **port série**. | ||
+ | * Cliquez l'îcone **Ouvrir**. | ||
+ | * Sélectionnez le menu **Contrôle**. | ||
+ | * Cliquez le bouton **Débloquer**. | ||
- | ==== 4. Roughly locate the Router/bit to starting location and turn on CNC machine power ==== | + | \\ |
+ | ===== 6. Préparez le nivelage automatique ===== | ||
+ | * Sélectionnez le menu **Fichier**. | ||
+ | * Charger le fichier gcode du contour de votre circuit, cela permettra de sélectionner simplement la zone à tester pour la mise à niveau automatique. | ||
+ | * Positionnez la broche à peu près au point de départ. FIXME //lien Jog// | ||
+ | * Sélectionnez le menu **Sonde** et le sous-menu **Sonde**. | ||
+ | * Mettez à zéro X et Y en cliquant sur **X=0** et **Y=0**. | ||
+ | * cliquez sur le bouton **Afficher en entier** ou (**F**) au clavier. | ||
+ | * Descendez le foret à quelques mm du PCB en utilisant les contrôles du jog. | ||
+ | * Mettez à zéro Z en cliquant sur **Z=0**. | ||
+ | * Dans la section **sonde** renseignez le champ Pos Z à -10. Cela permetra au foret de descendre de 10 mm pour sonder avant de déclencher une alarme. | ||
+ | * Important : **Fixez les pinces de sonde au PCB et au foret**. Sinon il y a risque de casse ! | ||
+ | * Dans la section **sonde** cliquez le bouton sonde : **le foret descend et s'arrête au contact du cuivre**. | ||
+ | * Mettez à nouveau à zéro Z en cliquant sur **Z=0**. | ||
+ | * Remontez Z de 1 mm avec les contrôles du jog. | ||
- | ==== 5. Start bCNC ==== | + | |
+ | \\ | ||
+ | ===== 7. Nivelage automatique ===== | ||
+ | * Dans le menu **Sonde** et le sous menu **Nivelage automatique**. | ||
+ | * Cliquez sur le bouton **Marges**. Cela va configurer automatiquement une zone de nivelage automatique calquée sur les limites de votre fichier gcode. Cette zone est représenté par une grille. | ||
+ | * Dans la section **Nivelage automatique**, vous pouvez ajuster le nombre de points X/Y testés en modifiant les valeurs N. Les champs **pas** indiquent l'espacement des points à tester. | ||
+ | * Renseignez Z Min à -10 et Z Max à 0.5. Dans le cas d'une grande déviation en hauteur sur la longueur du circuit, mettez une plus grande valeur dans Z max (et peut-être il faudra penser à surfacer le martyr et/ou remettre à niveau la machine) | ||
+ | * Important : **Vérifiez que les pinces de sonde sont bien fixées au PCB et au foret**. | ||
+ | * Dans le menu **Sonde** et le sous menu **Nivelage automatique** cliquez sur le bouton **Scanner** : La machine vient tester chaque point. | ||
+ | * Retournez au zéro X/Y. Dans le champ **Commande** (tout en bas) tappez : **G0 X0 Y0** | ||
+ | * Retournez au zéro Z. Dans le champ **Commande** (tout en bas) tappez : **G0 Z0** | ||
+ | * Dans le menu **Sonde** et le sous menu **Nivelage automatique** cliquez sur le bouton **Zéro** pour valider le scan. | ||
+ | * **Retirez les pinces de sonde**. | ||
- | ==== 6. Connect to CNC via bCNC ==== | + | |
- | * Select File Menu | + | \\ |
- | * Select Serial Port | + | ===== 9. Chargez le 1er gcode de perçage ===== |
- | * Click on Open | + | * Sélectionnez le menu **Fichier**. |
- | * Select Control Menu | + | * Charger le 1er fichier gcode de perçage. |
- | * Click on Unlock | + | * Répondez non au dialogue "Probe File modified". |
- | ==== 7. Prepare for Autoleveling ==== | + | * Répondez non au dialogue "Existing Autolevel". |
- | * Select File Menu | + | * //Option// - Dans le menu déroulant **Changer l'angle de vue** choisissez une vue ISO. |
- | * Open gcode file for cutout routing - this will make it simple to setup the correct Autolevel area | + | |
- | * Position bit to X and Y start location using Control widgets. | + | |
- | * Select Probe Menu | + | \\ |
- | * Click on Probe Submenu | + | ===== 10. Percez ===== |
- | * Zero out X and Y by Clicking on X=0 the Y=0 | + | |
- | * Click on "fit to screen" button | + | |
- | * Lower tool bit within a couple of mm of PCB using jog controls | + | |
- | * Zero out Z by Clicking on Z=0 | + | |
- | * In Probe menu, Probe section, Set the Z Pos: to -10 - this will allow the bit to go 10mm down to probe before setting off an alarm. | + | |
- | * **ATTACH PROBE CLIPS TO PCB AND TOOL BIT - FAILURE TO DO SO BEFORE PROCEEDING MAY RESULT IN A DAMAGED BIT.** | + | |
- | * Click Probe button (in Probe: section) | + | |
- | * Zero out Z axis - Click on Z=0 | + | |
- | * Raise Z by 1mm using jog | + | |
- | ==== 8. Autolevel ==== | + | |
- | * Under Probe Menu, Select Autolevel Submenu | + | |
- | * Click on Margins - This will configure an autolevel area mapped to you gcode file limits | + | |
- | * modify number of X/Y test points as needed by adjusting N for X and Y | + | |
- | * set Z Min to -10 and Z Max to 0.5 - if you expect a large deviation in height across the board, set Z max to a higher value ( and perhaps consider leveling waste board and/or machine) | + | |
- | * **CONFIRM PROBE CLIPS TO PCB AND TOOL BIT - FAILURE TO DO SO BEFORE PROCEEDING MAY RESULT IN A DAMAGED BIT.** | + | |
- | * Click on Scan | + | |
- | * Return to X/Y zero - in Command: (at bottom) enter G0 X0 Y0 | + | |
- | * Return to Z zero - in Command: (at bottom) enter G0 Z0 | + | |
- | * At top click at "Zero" in menu for Autolevel to adjust measured values (@vlachoudis: why this is required?) | + | |
- | * REMOVE PROBE CONNECTION TO TOOL BIT. | + | |
- | ==== 9. Load first Drill gcode file ==== | + | |
- | * Under File menu select Open and select drill file | + | |
- | * Answer no to the "Probe File modified" dialog | + | |
- | * Answer no to the "Existing Autolevel" dialog | + | |
- | * Optional - Select ISO view from "Change viewing Angle" widget. | + | |
- | ==== 10. Perform Drilling operation ==== | + | |
* Confirm that you've REMOVED THE PROBE CONNECTION TO THE TOOL BIT. | * Confirm that you've REMOVED THE PROBE CONNECTION TO THE TOOL BIT. | ||
* If manually controlling power to your router, turn it on now. | * If manually controlling power to your router, turn it on now. | ||
Ligne 67: | Ligne 81: | ||
* Click on Start. | * Click on Start. | ||
* When drilling is complete, if manually controlling power to your router, turn it off. | * When drilling is complete, if manually controlling power to your router, turn it off. | ||
- | ==== 11. Change Tool Bit - Do this every time you change a bit, whether it be a drill, routeing, or engraving bit ==== | + | |
+ | |||
+ | \\ | ||
+ | ===== 11. Changement d'outil ===== | ||
+ | |||
+ | // Répétez cette étape à chaque fois que vous changez d'outil, que ce soit un foret de perçage, une pointe de gravure ou une fraise.// | ||
* Raise Z to comfortable height using jog controls. | * Raise Z to comfortable height using jog controls. | ||
* Replace Tool bit | * Replace Tool bit | ||
Ligne 79: | Ligne 99: | ||
* Raise Z by 1mm using jog controls. | * Raise Z by 1mm using jog controls. | ||
* REMOVE PROBE CONNECTION TO TOOL BIT. | * REMOVE PROBE CONNECTION TO TOOL BIT. | ||
- | ==== 12. If performing more Drilling operations, follow steps 10-12, with final Tool bit change being to the trace routing bit ==== | + | |
- | ==== 13. Load trace routing gcode file ==== | + | |
+ | \\ | ||
+ | ===== 12. If performing more Drilling operations, follow steps 10-12, with final Tool bit change being to the trace routing bit ===== | ||
+ | |||
+ | |||
+ | \\ | ||
+ | ===== 13. Load trace routing gcode file ===== | ||
* Under FIle menu select Open and select trace routing gcode file | * Under FIle menu select Open and select trace routing gcode file | ||
- | * Answer no to the "Probe File modified" dialog | + | * Répondez non au dialogue "Probe File modified". |
- | * Answer no to the "Existing Autolevel" dialog | + | * Répondez non au dialogue "Existing Autolevel". |
- | * Optional Select preferred viewing angle. | + | * //Option// - Dans le menu déroulant **Changer l'angle de vue** choisissez une vue ISO. |
- | ==== 14. Change Tool Bit per step 11 ==== | + | |
- | ==== 15. Perform Trace Routing operation ==== | + | |
+ | \\ | ||
+ | ===== 14. Change Tool Bit per step 11 ===== | ||
+ | |||
+ | |||
+ | \\ | ||
+ | ===== 15. Perform Trace Routing operation ===== | ||
* Confirm that you've **REMOVED THE PROBE CONNECTION TO THE TOOL BIT.** | * Confirm that you've **REMOVED THE PROBE CONNECTION TO THE TOOL BIT.** | ||
* If manually controlling power to your router, turn it on now. | * If manually controlling power to your router, turn it on now. | ||
Ligne 92: | Ligne 124: | ||
* Click on Start. | * Click on Start. | ||
* When routing is complete, if manually controlling power to your router, turn it off. | * When routing is complete, if manually controlling power to your router, turn it off. | ||
- | ==== 16. Load Outline routing gcode file ==== | + | |
+ | |||
+ | \\ | ||
+ | ===== 16. Load Outline routing gcode file ===== | ||
* Under FIle menu select Open and select outline routing gcode file | * Under FIle menu select Open and select outline routing gcode file | ||
- | * Answer no to the "Probe File modified" dialog | + | * Répondez non au dialogue "Probe File modified". |
- | * Answer no to the "Existing Autolevel" dialog | + | * Répondez non au dialogue "Existing Autolevel". |
- | * Optional - Select preferred viewing angle. | + | * //Option// - Dans le menu déroulant **Changer l'angle de vue** choisissez une vue ISO. |
- | ==== 17. Change Tool Bit per step 12 ==== | + | |
- | ==== 18. Perform outline Routing operation ==== | + | |
+ | \\ | ||
+ | ===== 17. Change Tool Bit per step 12 ===== | ||
+ | |||
+ | |||
+ | \\ | ||
+ | ===== 18. Perform outline Routing operation ===== | ||
* Confirm that you've **REMOVED THE PROBE CONNECTION TO THE TOOL BIT.** | * Confirm that you've **REMOVED THE PROBE CONNECTION TO THE TOOL BIT.** | ||
* If manually controlling power to your router, turn it on now. | * If manually controlling power to your router, turn it on now. |